RAPCO
Cleveland
McCauley Piper
Bolt Holes
Quan. - Size
Slotted
Disc
Minimum Wear
Thickness in / mmCurrent Superseded
RA164-06700 164-06700 164-67 754-615 6 - 1/4” 0.220 / 5.588
RA164-06900 164-06900 164-69 3 - 5/16” 0.205 / 5.207
RA164-07200 164-07200 164-72 8 - 3/8” Slotted 0.492 / 12.497
RA164-07400 164-07400 164-74 8 - 5/16” Slotted 0.492 / 12.497
RA164-07500 * 164-07500 164-75 3 - 5/16” 0.205 / 5.207
RA164-07700 164-07700 164-77 754-642 9 - 5/16” Slotted 0.470 / 11.938
RA164-07800 164-07800 164-78 6 - 5/16” Slotted 0.450 / 11.430
RA164-07906 164-07906
164-05200
164-79F
164-52
9 - 1/4” Slotted 0.465 / 11.811
RA164-08100 * 164-08100 164-81 6 - 5/16” Slotted 0.450 / 11.43
RA164-08200 164-08200 164-82 6 - 5/16” Slotted 0.327 / 8.306
RA164-08300 164-08300 164-83 6 - 5/16” 0.327 / 8.306
RA164-08406 164-08406 164-84F 6 - 5/16” Slotted 0.330 / 8.382
RA164-08500 164-08500 164-85 3 - 1/4” 0.325 / 8.255
RA164-09100 164-09100 164-91 9 - 5/16” Slotted 0.492 / 12.497
RA164-09900 * 164-09900 164-99 3 - 1/4” 0.275 / 6.985
RA164-20206 164-20206 164-202F 9 - 5/16” 0.334 / 8.484
RA164-20306 164-20306 164-203F 6 - 5/16” Slotted 0.465 / 11.811
RA164-20500 164-20500 164-205 6 - 5/16” Slotted 0.525 / 13.335
RA164-20600 164-20600 164-206 754-658 8 - 5/16” Slotted 0.455 / 11.557
RA164-20700 164-20700 164-207 8 - 5/16” Slotted 0.410 / 10.414
RA164-20806 164-20806 164-208F 6 - 5/16”
Slotted 0.475 / 12.065
RA164-20900 164-20900 164-209 8 - 3/8” Slotted 0.410 / 10.414
RA164-21000 164-21000 164-210 6 - 3/8” Slotted 0.436 / 11.074
RA164-21100 164-21100 164-211 9 - 5/16” Slotted 0.492 / 12.497
RA164-21200 164-21200 164-212 9 - 5/16” 0.327 / 8.306
RA164-21600 164-21600 164-216 754-686 6 - 5/16” Slotted 0.405 / 10.287
RA164-21900 164-21900 164-219 9 - 5/16” Slotted 0.590 / 14.986
RA164-22000 164-22000 164-220 8 - 3/8” Slotted 0.360 / 9.144
RA164-22201 164-22201 164-222A 9 - 5/16” Slotted 0.537 / 13.640
RA164-22202 164-22202 164-222B 9 - 5/16” Slotted 0.537 / 13.640
RA164-22400 164-22400 164-224 9 - 3/8” Slotted 0.385 / 9.779
RA164-22900 164-22900 164-229 8 - 3/8” Slotted 0.410 / 10.414
RA164-23000 164-23000 164-230 9 - 3/8” Slotted 0.565 / 14.351
RA164-24200 164-24200 3 - 1/4” 0.167 / 4.242
RA164-24400 164-24400 3 - 1/4” 0.366 / 7.366
RA164-30195 164-30195 164-09300
164-93
B-30195 6 - 5/16” 0.190 / 4.826
RA164-30388 164-30388 164-09700
164-97
C-30388 6 - 5/16” 0.325 / 8.255
RA164-30398 164-30398 164-09600
164-96
C-30398 6 - 5/16” 0.325 / 8.255
RA164-30414 164-30414 164-09500
164-95
C-30414 6 - 5/16” 0.325 / 8.255
RA164-30440 164-30440 164-09200
164-92
B-30440
C-30615-4
6 - 5/16” 0.190 / 4.826
RA164-30615-1 164-30615-1 164-08800
164-88
C-30615-1 3 - 5/16” 0.190 / 4.826
RA164-30615-2 164-30615-2 164-08900
164-89
C-30615-2 3 - 5/16” 0.330 / 8.382
RA164-30615-3 164-30615-3
164-09000
164-90
C-30615-3 3 - 5/16” 0.330 / 8.382
* Indicates a disk part number for use on experimental aircraft.
** For minimum wear thickness on Piper Aztec brake disc RA164-00206 or RA164-03206 perform the following procedure. First measure the linings to make sure they
are each above the minium wear of 0.100 inch or ( 0.76 mm ) thick, if not replace. Next measure the cumulative thickness of the two linings, the pressure plate and the
brake disk. If the cumulative thickness of these four items is less than 1.00 inch ( 25.40 mm ) the disc is considered to be below minimum wear thickness and should be
replaced. For reference only.
Section 5 - Cross Reference
Brake Discs
Pneumatics
Deice
Filters
Gaskets
corP & reGional
Brakes
Fuel PumPs
miscellaneous
Pneumatics
Ga Brakes
83